Felix 3.0 Dual - Slizer setting shown in manual not availabl

Discussions about firmware/slicing software, tweaks and settings
Post Reply
frankjoke
Posts: 150
Joined: Sat Dec 28, 2013 6:07 pm

Re: Felix 3.0 Dual - Slizer setting shown in manual not avai

Post by frankjoke » Sun Jan 26, 2014 12:45 am

Ok.my first completed 2-head print with PLA and PVA :)

PLA @195 and PVA @175 with 20 of speed only...

Sorry, all my pics are turned left... Need to manage beter!
Attachments
2014-01-26 00.37.34.jpg
To take it off
2014-01-25 22.42.01.jpg
Printing

Kjetilei
Posts: 334
Joined: Fri Mar 16, 2012 8:26 pm
Location: Stavanger, Norway

Post by Kjetilei » Sun Jan 26, 2014 1:44 am

Congratulations :) Was the PVA (white filament) printed as support? I'm questioning since it protrudes compared to the red filament.

frankjoke
Posts: 150
Joined: Sat Dec 28, 2013 6:07 pm

Post by frankjoke » Sun Jan 26, 2014 1:53 am

Yes, the natural PVA was support, the file was generated with Kisslicer.

There were 5 attemts before with either too high temperature for PVA or too high spped (for both) because PVA does not stick well on anything and is very weak!

I swtched off bed heating and fan after first 2 layers. I use inkjet transparents on my bed, everything sticks better than on glass or kepton.

frankjoke
Posts: 150
Joined: Sat Dec 28, 2013 6:07 pm

Post by frankjoke » Sun Jan 26, 2014 2:12 am

This 3x3 cm model took 2.5h to print but dissolved PVA in warm water only in <2h!
Attachments
2014-01-26 02.06.07.jpg
The final thing without any other rework, just without PVA!

Mayhem
Posts: 169
Joined: Tue Jan 08, 2013 4:15 pm
Location: Finland

Post by Mayhem » Sun Jan 26, 2014 8:38 am

Nice :o
Felix 2.0----> 3.0
V4 hot end
Simplyfy 3D
Kisslicer
Autodesk fusion 360

Makron
Posts: 110
Joined: Wed Mar 20, 2013 1:29 pm

Post by Makron » Sun Jan 26, 2014 9:33 am

Very Very nice !!!! more pics and movies pls !!

Saamec
Posts: 157
Joined: Fri Jun 21, 2013 9:28 am

Post by Saamec » Sun Jan 26, 2014 3:00 pm

Surface quality is not very good, Felix may even better. If the printer is printing c PVA supports, snot plastic should be nowhere. This thing does not sell in the store.

Makron
Posts: 110
Joined: Wed Mar 20, 2013 1:29 pm

Post by Makron » Sun Jan 26, 2014 4:32 pm

Saamec wrote:Surface quality is not very good, Felix may even better. If the printer is printing c PVA supports, snot plastic should be nowhere. This thing does not sell in the store.

????????????????????????????????????????????????????????????????????????????????

frankjoke
Posts: 150
Joined: Sat Dec 28, 2013 6:07 pm

Post by frankjoke » Sat Feb 01, 2014 12:08 am

The printed cube is only 3cm of total size and the layer height was 0.2mm.
So of course, I could do better but I did not want to wait hours to find out that print does not work after 50 layers ...

If you have better settings for the PLA & PVA to create better prints on Felix it would be great to hear!

Saamec
Posts: 157
Joined: Fri Jun 21, 2013 9:28 am

Post by Saamec » Sat Feb 01, 2014 12:42 am

Enable the Skin vertical division 3, 2 horizontal. Perimeter Fill in the parameter set to 2. You in filling the layer thickness of 0.2, there is a layer on the walls of equal 0.066666... not much time will increase printing, but the quality of execution will be 3 times better!!! so on...

Post Reply