updating firmware

Discussions about firmware/slicing software, tweaks and settings
Post Reply
stillcool40
Posts: 33
Joined: Sun Mar 30, 2014 1:59 pm

updating firmware

Post by stillcool40 » Wed Oct 08, 2014 8:53 am

Being new to this I can't find any instructions on how you actually update the felix firmware.

am I missing something somewhere?

:roll:

satoer
Posts: 436
Joined: Mon Oct 01, 2012 8:00 pm
Location: Netherlands

Post by satoer » Wed Oct 08, 2014 9:46 am

My Felix 1.5 printed designs on Thingiverse
E3D V6 Hot end upgrade for your Felix
Tweezer bracket for your Felix
Led bar upgrade for your Felix

stillcool40
Posts: 33
Joined: Sun Mar 30, 2014 1:59 pm

Post by stillcool40 » Wed Oct 08, 2014 10:50 am

yea i found it thanks

stillcool40
Posts: 33
Joined: Sun Mar 30, 2014 1:59 pm

Post by stillcool40 » Wed Oct 08, 2014 11:06 am

I have downloaded the repetier single extruder firmware and followed all instructions, Arduino produces lots of compile errors when you hit upload.

im using arduino 1.5.8 downloaded this week

help

Makron
Posts: 110
Joined: Wed Mar 20, 2013 1:29 pm

Post by Makron » Wed Oct 08, 2014 12:50 pm

What is the error ?

Do you have the control panal on youre felix that is probably where the porblem is

stillcool40
Posts: 33
Joined: Sun Mar 30, 2014 1:59 pm

Post by stillcool40 » Wed Oct 08, 2014 4:03 pm

there are LOTS of errors, sounds like the sketch is in the wrong arduino or something.

stillcool40
Posts: 33
Joined: Sun Mar 30, 2014 1:59 pm

Post by stillcool40 » Wed Oct 08, 2014 4:04 pm

and I dont have control panel

frankjoke
Posts: 150
Joined: Sat Dec 28, 2013 6:07 pm

Post by frankjoke » Wed Oct 08, 2014 10:06 pm

I did compile with 1.5.5 without an error but with 1.5.8 I get:
ui.cpp: In member function 'void UIDisplay::adjustMenuPos()':
ui.cpp:2097:47: error: ISO C++ forbids declaration of 'type name' with no type [-fpermissive]
uint8_t mtype = HAL::readFlashByte((const prog_char*)&(men->menuType));
^
ui.cpp:2097:47: error: ISO C++ forbids declaration of 'type name' with no type [-fpermissive]
ui.cpp:2097:41: error: expected primary-expression before 'const'
uint8_t mtype = HAL::readFlashByte((const prog_char*)&(men->menuType));
^
ui.cpp:2097:41: error: expected ')' before 'const'
ui.cpp: In member function 'void UIDisplay::nextPreviousAction(int8_t)':
ui.cpp:2164:47: error: ISO C++ forbids declaration of 'type name' with no type [-fpermissive]
uint8_t mtype = HAL::readFlashByte((const prog_char*)&(men->menuType));
^
ui.cpp:2164:47: error: ISO C++ forbids declaration of 'type name' with no type [-fpermissive]
ui.cpp:2164:41: error: expected primary-expression before 'const'
uint8_t mtype = HAL::readFlashByte((const prog_char*)&(men->menuType));
^
ui.cpp:2164:41: error: expected ')' before 'const'
ui.cpp:2169:49: error: ISO C++ forbids declaration of 'type name' with no type [-fpermissive]
uint8_t entType = HAL::readFlashByte((const prog_char*)&(ent->menuType));
^
ui.cpp:2169:49: error: ISO C++ forbids declaration of 'type name' with no type [-fpermissive]
ui.cpp:2169:43: error: expected primary-expression before 'const'
uint8_t entType = HAL::readFlashByte((const prog_char*)&(ent->menuType));
^
ui.cpp:2169:43: error: expected ')' before 'const'
Error compiling.

stillcool40
Posts: 33
Joined: Sun Mar 30, 2014 1:59 pm

Post by stillcool40 » Thu Oct 09, 2014 7:54 am

this is similar to the errors mine is producing.

Makron
Posts: 110
Joined: Wed Mar 20, 2013 1:29 pm

Post by Makron » Thu Oct 09, 2014 10:12 pm

Can you .rar the firmware and send it to kuupeetje@makron.nl then i can look at it

Also type what board you are using ramps of the felix one , and if you have the panal/display unit.

Post Reply