General

General discussions regarding hardware
New Topic
  • Topics
    Replies
    Views
    Last post
  • Extruder Stepper bug
    by TBaden » Fri Feb 27, 2015 2:58 pm
    1 Replies
    2616 Views
    Last post by frankjoke
    Fri Feb 27, 2015 10:20 pm
  • Extruder v4 faillure, resolving the issue with E3D v6!!
    by Eli-Audio » Fri Jan 02, 2015 8:17 pm
    17 Replies
    4600 Views
    Last post by alanh
    Fri Feb 27, 2015 1:50 pm
  • 3d printed object smaller than drawing
    by neilv » Sun Feb 22, 2015 8:48 am
    7 Replies
    3802 Views
    Last post by neilv
    Tue Feb 24, 2015 8:52 am
  • Opto sensors
    by nosomis » Mon Jan 05, 2015 2:54 pm
    8 Replies
    3644 Views
    Last post by Dreide
    Sat Jan 17, 2015 11:00 am
  • Missing printable parts for 2.0
    by Mellin » Sat Jan 10, 2015 6:30 pm
    0 Replies
    2761 Views
    Last post by Mellin
    Sat Jan 10, 2015 6:30 pm
  • Hot-end isolation peek gets melted
    by mmurin » Mon Jan 05, 2015 3:08 am
    1 Replies
    2806 Views
    Last post by Jaanus
    Sat Jan 10, 2015 7:33 am
  • extruder temperature sensor
    by cx32 » Fri Jan 02, 2015 1:33 am
    2 Replies
    3012 Views
    Last post by cx32
    Fri Jan 09, 2015 9:57 pm
  • Stepper not working-connector? Electrical board?
    by Caliprint » Sat Oct 11, 2014 3:30 am
    4 Replies
    3320 Views
    Last post by sajjad123
    Sun Dec 07, 2014 9:20 am
  • ViKi LCD - How To Connect to Felix 2
    by mrlate » Sun Nov 16, 2014 3:31 am
    1 Replies
    2719 Views
    Last post by Makron
    Sun Nov 16, 2014 8:25 am
  • nozzle spec question
    by cstead » Thu Nov 06, 2014 2:49 am
    1 Replies
    2725 Views
    Last post by cstead
    Thu Nov 06, 2014 10:26 pm
  • Extruder does not react
    by immi1988 » Wed Oct 29, 2014 5:58 pm
    4 Replies
    796 Views
    Last post by immi1988
    Sat Nov 01, 2014 7:49 am
  • Felix 3.0 controller not printing
    by kellsteinman » Thu Jun 26, 2014 7:57 am
    3 Replies
    794 Views
    Last post by kerog
    Tue Oct 21, 2014 2:52 am
  • Heaters decoupled
    by Retrofire » Tue Sep 30, 2014 12:29 pm
    4 Replies
    3360 Views
    Last post by kerog
    Tue Oct 21, 2014 2:51 am
  • Hot end fell out
    by slave » Mon Sep 15, 2014 7:22 pm
    4 Replies
    812 Views
    Last post by viljmak
    Tue Sep 16, 2014 12:19 pm
  • printer freezes when opening/closing light switch
    by Hugues » Thu May 22, 2014 5:51 am
    12 Replies
    1755 Views
    Last post by WayneC
    Tue Sep 02, 2014 12:38 pm
  • Where can I buy the plastic hot-end heat separator?
    by satoer » Fri Nov 02, 2012 5:14 pm
    6 Replies
    2556 Views
    Last post by JohnK1
    Thu Aug 21, 2014 9:27 pm
  • Warped box
    by tomasf » Fri Aug 15, 2014 10:28 am
    1 Replies
    608 Views
    Last post by tomasf
    Tue Aug 19, 2014 1:54 pm
New Topic

Forum permissions

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum